The parameters obtained become the active parameters immediately.
Bootp When the initialization mode “Bootp” is selected, the card tries to download the parameters from a Bootp Server. Initialization Mode Selection The following initialization modes are selectable: NOTE Compared to the G1369A LAN card, SW 7 and SW 8 must always be in OFF position on the G1369B LAN card, otherwise the selected modes are not working. When finished, click Exit Manager, the select OK. Repeat from step 5 for any additional instruments.
Enter MAC address, host name, IP address, Comment (if desired), subnet mask, and gateway address. Select Add... The Add Bootp Entry screen appears. Uncheck Do you want to log BootP requests? c. Follow Start > Programs > Agilent BootP Service > Edit BootP Settings b.
4.Īssigning IP addresses to instruments with Jet Direct cards IP addresses for the 6890A, 6890 Plus, 35900E, and 6850A with a Jet Direct card can be configured by using the following methods: In the Target field, enter the current GC IP address 3. From the Windows® Start program menu, Agilent > All Programs > Agilent Technologies > 7820A GC Remote Controller. During installation this IP address can change or be set to use DHCP.
The initial installation r equir es that you connect the software keypad dir ectly to the GC using this address. Confirm that the correct setpoints are present. Power cycle the instrument to apply the LAN setpoints to the card. The GC displays a message instructing you to power cycle the instrument. Scroll to the appropriate subnet mask from the list of modes and press. When prompted, turn the GC off and then on again. Scroll to Enable DHCP and, if necessary, press to disable DHCP.
Setting IP addresses from instrument keypad When entering an IP address at an instrument, be sure it is correct and is not in use by another device (such as a printer). Instrument Firmware Requirements Table 1: Instrument Requirements Instrument Type Model Supported instrument firmware revision Method for setting IP addresses 7890A G3440A A.01.10.3 Set at GC keypad 7820A G4350A 7820A.01.10.013.1.bin (E,C,J) 7820A.01.10.013.Ru.bin Set using software keypad 6890N GC G1530N/ G1540N N.06.A And N.05.06 LAN Assembly Firmware 04.7B3 Set at GC keypad 6890 Plus, 6890A G1530A/ G1540A A.03.08 Chip Set Determined by Jet Direct card used – see below. The second type of instrument requires the IP address to be assigned using either Agilent BootP or Telnet. The first type of instrument allows the IP address to be entered directly at the GC.
There are two types of instruments that can be added to either the local or site LAN.
Instruments on the LAN Each LAN instrument requires a unique IP address on the same subnet as the ChemStation PC to work correctly on the network. From the Local Area Connection Properties screen highlight Internet Protocol version 4 and select Properties. Then select Local Area Connection > Properties. Windows 7: Select Start > Control Panel > Network and Sharing Center. Windows Vista: Select Start > Control Panel > Network and Sharing > Manage Network Connections. All PCs and instruments they control must be on the same subnet. Depending on your site LAN administrator’s direction, PCs added for instrument control can obtain LAN addresses automatically from the site’s DHCP server, or have fixed IP addresses. The LAN site administrator assigns fixed IP addresses for each instrument you are adding to the network.
This manual covers instrument LANs for the following instruments: Identifying the Required Instrument LAN An instrument LAN consists of one or more data system computers and instruments. 10 Setting the IP address for a 7890A GC. 9 Setting IP addresses from instrument keypad. The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions.Ĭontents Identifying the Required Instrument LAN. as governed by United States and international copyright laws. 2010 Warranty No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. Setting up a LAN Instrument Network Installation Guide